Search found 9 matches

Return to advanced search

Re: Burned C18 on my PA100-D

Hi, Here are some feedback about this issue. The fact I use a end feeded wire antenna, the SWR an some bands are not like 1:1. Some have 1:2 or 1:3. To overcome burned capacitors in the future, I decided to replace all of them with mica types rated for 500V. Unfortunately they are so much bigger, yo...
by HB9FZG
13 May 2016 20:56
 
Forum: Juma Discussion
Topic: Burned C18 on my PA100-D
Replies: 2
Views: 3790

Re: try to upgrade

Hi Erich, This is the code of file ibl_dspiclist.xml <?xml version="1.0" encoding="iso-8859-1"?> <!DOCTYPE devices SYSTEM "ingeniadspicbootloader.dtd"> <devices> <device id="0x01C1" name="dsPIC3011"> <memcode startaddress="0x000000" endaddr...
by HB9FZG
13 May 2016 12:36
 
Forum: Juma Firmware by 5B4AIY
Topic: try to upgrade
Replies: 6
Views: 16034

Burned C18 on my PA100-D

After running the PA100-D at 40m with about 7 Watts in G1? mode, some smoke came out of the unit. The culprit was C18 burned black. Any advice for a replacement?

73,
Uwe
by HB9FZG
05 May 2016 22:06
 
Forum: Juma Discussion
Topic: Burned C18 on my PA100-D
Replies: 2
Views: 3790

Re: Build Environment ???

Hi,

Half of the job has been done. I was able to program the CPU with the hex file containing version 1.04 and bootloader. Then I updated to 2.00b.v4 without any hickups.Next steps are bringing the legacy code to live on the current dev environment.

73,Uwe
by HB9FZG
05 May 2016 21:58
 
Forum: Juma Firmware by 5B4AIY
Topic: Build Environment ???
Replies: 5
Views: 17382

Re: Problem flashing Firmware

Hi Adrian

The PICKit3 arrived yesterday. So I was able to program the CPU with the HEX containing software and bootloader. The update to V2b-04 was also very easy. I will start a new thread about porting your source to the new development environment.

Thank you very much for your support.

73,
Uwe
by HB9FZG
05 May 2016 21:26
 
Forum: Juma Discussion
Topic: Problem flashing Firmware
Replies: 19
Views: 25156

Re: Build Environment ???

Hi guys, Enhancing the firmware code, I have several obstacles to avoid. The development environment Adrian is using is no longer available for free. Compiling the code in the current free environment throws a lot of errors. As I'am new to Microchip hardware, I may need some help from the community ...
by HB9FZG
04 May 2016 14:35
 
Forum: Juma Firmware by 5B4AIY
Topic: Build Environment ???
Replies: 5
Views: 17382

Re: Problem flashing Firmware

Hi,

I have the same problem with my new PA100-D. Software is 1.04. Holding the OPER button during power on only brings up a message to press SET to do factory reset (which BTN is SET?)
RS232 is working fine.

Sadly, that I have to buy a extra programmer to update the firmware :roll:

73,
Uwe
by HB9FZG
02 May 2016 20:29
 
Forum: Juma Discussion
Topic: Problem flashing Firmware
Replies: 19
Views: 25156

Build of my PA100-D near finished

Hi

Today my new PA100-D got powered up and everything seems working. Next is to set the bias currrent and do some testing with my M0NKA radio.
by HB9FZG
30 Apr 2016 22:17
 
Forum: Juma Discussion
Topic: Build of my PA100-D near finished
Replies: 0
Views: 3898

Re: Build Environment ???

I'am in the same situation as Bob. I want to run the PA in remote operation. It would be nice to read some status info over RS232 and show that on a webpage.

Maybe someone has already made some extension in the code?

73, Uwe, HB9FZG
by HB9FZG
21 Apr 2016 20:47
 
Forum: Juma Firmware by 5B4AIY
Topic: Build Environment ???
Replies: 5
Views: 17382

Return to advanced search